Facebook
From Kyashan, 2 Weeks ago, written in Plain Text.
Embed
Download Paste or View Raw
Hits: 56
  1. # For more options and information see
  2. # http://rpf.io/configtxt
  3. # Some settings may impact device functionality. See link above for details
  4.  
  5. # uncomment if you get no picture on HDMI for a default "safe" mode
  6. #hdmi_safe=1
  7.  
  8. # uncomment this if your display has a black border of unused pixels visible
  9. # and your display can output without overscan
  10. #disable_overscan=1
  11.  
  12. # uncomment the following to adjust overscan. Use positive numbers if console
  13. # goes off screen, and negative if there is too much border
  14. #overscan_left=16
  15. #overscan_right=16
  16. #overscan_top=16
  17. #overscan_bottom=16
  18.  
  19. # uncomment to force a console size. By default it will be display's size minus
  20. # overscan.
  21. #framebuffer_width=1280
  22. #framebuffer_height=720
  23.  
  24. # uncomment if hdmi display is not detected and composite is being output
  25. #hdmi_force_hotplug=1
  26.  
  27. # uncomment to force a specific HDMI mode (this will force VGA)
  28. #hdmi_group=1
  29. #hdmi_mode=1
  30.  
  31. # uncomment to force a HDMI mode rather than DVI. This can make audio work in
  32. # DMT (computer monitor) modes
  33. #hdmi_drive=2
  34.  
  35. # uncomment to increase signal to HDMI, if you have interference, blanking, or
  36. # no display
  37. #config_hdmi_boost=4
  38.  
  39. # uncomment for composite PAL
  40. #sdtv_mode=2
  41.  
  42. #uncomment to overclock the arm. 700 MHz is the default.
  43. #arm_freq=800
  44.  
  45. # Uncomment some or all of these to enable the optional hardware interfaces
  46. #dtparam=i2c_arm=on
  47. #dtparam=i2s=on
  48. #dtparam=spi=on
  49.  
  50. # Uncomment this to enable infrared communication.
  51. #dtoverlay=gpio-ir,gpio_pin=17
  52. #dtoverlay=gpio-ir-tx,gpio_pin=18
  53. dtoverlay=gpio-poweroff,gpiopin=19,active_low=1
  54.  
  55. # Additional overlays and parameters are documented /boot/overlays/README
  56.  
  57. # Enable audio (loads snd_bcm2835)
  58. dtparam=audio=on
  59. audio_pwm_mode=2
  60.  
  61. [pi4]
  62. # Enable DRM VC4 V3D driver on top of the dispmanx display stack
  63. #dtoverlay=vc4-fkms-v3d
  64. #max_framebuffers=2
  65.  
  66. [all]
  67. #dtoverlay=vc4-fkms-v3d
  68. #gpu_mem_256=128
  69. #gpu_mem_512=256
  70. #gpu_mem_1024=256
  71. overscan_scale=1
  72. gpu_mem=256
  73.  
  74. # Added by HyperPixel4 installation
  75. dtoverlay=hyperpixel4
  76. overscan_left=0
  77. overscan_right=0
  78. overscan_top=0
  79. overscan_bottom=0
  80. framebuffer_width=800
  81. framebuffer_height=480
  82. enable_dpi_lcd=1
  83. display_default_lcd=1
  84. display_rotate=1
  85. dpi_group=2
  86. dpi_mode=87
  87. dpi_output_format=0x7f216
  88. hdmi_timings=480 0 10 16 59 800 0 15 113 15 0 0 0 60 0 32000000 6
  89.  
  90.