root@DIR-825_openWRT:~# dmesg [ 0.000000] Linux version 4.14.209 (builder@buildhost) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11257-5090152ae3)) #0 Sun Dec 6 07:31:03 2020 [ 0.000000] MyLoader: sysp=2bfc520e, boardp=7193b0b9, parts=681a5619 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc) [ 0.000000] SoC: Atheros AR7161 rev 2 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] free_area_init_node: node 0, pgdat 804ecd50, node_mem_map 81000020 [ 0.000000] Normal zone: 128 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16384 pages, LIFO batch:3 [ 0.000000] random: get_random_bytes called from 0x804f0740 with crng_init=0 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: board=DIR-825-B1 console=ttyS0,115200 mtdparts=spi0.0:256k(uboot)ro,64k(config)ro,6208k(firmware),64k(caldata)ro,1600k(unknown)ro,64k@0x7f0000(caldata_copy) rootfstype=squashfs noinitrd [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=0002e3e0 [ 0.000000] Readback ErrCtl register=0002e3e0 [ 0.000000] Memory: 59320K/65536K available (3954K kernel code, 193K rwdata, 516K rodata, 320K init, 212K bss, 6216K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 51 [ 0.000000] Clocks: CPU:680.000MHz, DDR:340.000MHz, AHB:170.000MHz, Ref:40.000MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5621354254 ns [ 0.000008] sched_clock: 32 bits at 340MHz, resolution 2ns, wraps every 6316128254ns [ 0.007810] Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992) [ 0.074064] pid_max: default: 32768 minimum: 301 [ 0.078865] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.085468] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.094408] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.104269] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.111334] NET: Registered protocol family 16 [ 0.116908] MIPS: machine is D-Link DIR-825 rev. B1 [ 0.155457] ar71xx: invalid mac address "▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒ [ 0.189150] ar71xx: invalid mac address "▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒ [ 0.492460] registering PCI controller with io_map_base unset [ 0.498295] ar71xx: using random MAC address for eth0 [ 0.729565] ar71xx: using random MAC address for eth1 [ 2.620216] random: fast init done [ 2.879263] PCI host bridge to bus 0000:00 [ 2.883423] pci_bus 0000:00: root bus resource [mem 0x10000000-0x16ffffff] [ 2.890280] pci_bus 0000:00: root bus resource [io 0x0000] [ 2.895851] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 2.902620] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 2.910576] pci 0000:00:11.0: [168c:ff1d] type 00 class 0x020000 [ 2.910587] pci 0000:00:11.0: fixup device configuration [ 2.917107] pci 0000:00:11.0: reg 0x10: [mem 0x00000000-0x0000ffff] [ 2.917163] pci 0000:00:11.0: PME# supported from D0 D3hot [ 2.917326] pci 0000:00:12.0: [168c:ff1d] type 00 class 0x020000 [ 2.917335] pci 0000:00:12.0: fixup device configuration [ 2.923885] pci 0000:00:12.0: reg 0x10: [mem 0x00000000-0x0000ffff] [ 2.923935] pci 0000:00:12.0: PME# supported from D0 D3hot [ 2.924088] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 2.924113] pci 0000:00:11.0: BAR 0: assigned [mem 0x10000000-0x1000ffff] [ 2.930896] pci 0000:00:12.0: BAR 0: assigned [mem 0x10010000-0x1001ffff] [ 2.940498] clocksource: Switched to clocksource MIPS [ 2.946378] NET: Registered protocol family 2 [ 2.951536] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 2.958501] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 2.964906] TCP: Hash tables configured (established 1024 bind 1024) [ 2.971401] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 2.977236] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 2.983734] NET: Registered protocol family 1 [ 2.988119] PCI: CLS 0 bytes, default 32 [ 2.990448] Crashlog allocated RAM at address 0x3f00000 [ 2.996757] workingset: timestamp_bits=30 max_order=14 bucket_order=0 [ 3.007454] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 3.013323] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 3.030662] io scheduler noop registered [ 3.034586] io scheduler deadline registered (default) [ 3.040055] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 3.048132] console [ttyS0] disabled [ 3.071779] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 10625000) is a 16550A [ 3.080475] console [ttyS0] enabled [ 3.087441] bootconsole [early0] disabled [ 3.100757] m25p80 spi0.0: found s25sl064a, expected m25p80 [ 3.106339] m25p80 spi0.0: s25sl064a (8192 Kbytes) [ 3.111183] 6 cmdlinepart partitions found on MTD device spi0.0 [ 3.117088] Creating 6 MTD partitions on "spi0.0": [ 3.121894] 0x000000000000-0x000000040000 : "uboot" [ 3.128619] 0x000000040000-0x000000050000 : "config" [ 3.134781] 0x000000050000-0x000000660000 : "firmware" [ 3.150198] 2 uimage-fw partitions found on MTD device firmware [ 3.156181] 0x000000050000-0x0000001d3fb1 : "kernel" [ 3.161783] 0x0000001d3fb1-0x000000660000 : "rootfs" [ 3.167309] mtd: device 4 (rootfs) set to be root filesystem [ 3.173064] 1 squashfs-split partitions found on MTD device rootfs [ 3.179233] 0x000000450000-0x000000660000 : "rootfs_data" [ 3.186830] 0x000000660000-0x000000670000 : "caldata" [ 3.193075] 0x000000670000-0x000000800000 : "unknown" [ 3.199737] 0x0000007f0000-0x000000800000 : "caldata_copy" [ 3.206737] Realtek RTL8366S ethernet switch driver version 0.2.2 [ 3.212918] rtl8366s rtl8366s: using GPIO pins 5 (SDA) and 7 (SCK) [ 3.219186] rtl8366s rtl8366s: RTL8366 ver. 1 chip found [ 3.250560] rtl8366s rtl8366s: applying initvals [ 3.285164] libphy: rtl8366s: probed [ 3.289247] libphy: Fixed MDIO Bus: probed [ 3.318325] libphy: ag71xx_mdio: probed [ 3.662082] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii [ 4.002450] ag71xx ag71xx.1: connected to PHY at rtl8366s:04 [uid=001cc960, driver=Generic PHY] [ 4.011659] eth1: Atheros AG71xx at 0xba000000, irq 5, mode: rgmii [ 4.019482] NET: Registered protocol family 10 [ 4.028063] Segment Routing with IPv6 [ 4.031867] NET: Registered protocol family 17 [ 4.036347] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 4.049756] 8021q: 802.1Q VLAN Support v1.8 [ 4.055350] hctosys: unable to open rtc device (rtc0) [ 4.065499] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 4.073564] Freeing unused kernel memory: 320K [ 4.078000] This architecture does not have kernel memory protection. [ 4.735333] init: Console is alive [ 4.738949] init: - watchdog - [ 5.734357] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 5.791131] usbcore: registered new interface driver usbfs [ 5.796696] usbcore: registered new interface driver hub [ 5.802119] usbcore: registered new device driver usb [ 5.811509] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 5.819431] ehci-platform: EHCI generic platform driver [ 5.824790] ehci-platform ehci-platform: EHCI Host Controller [ 5.830583] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 5.838584] ehci-platform ehci-platform: irq 3, io mem 0x1b000000 [ 5.870530] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00 [ 5.877480] hub 1-0:1.0: USB hub found [ 5.881573] hub 1-0:1.0: 2 ports detected [ 5.888185] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 5.895528] ohci-platform: OHCI generic platform driver [ 5.900893] ohci-platform ohci-platform: Generic Platform OHCI controller [ 5.907684] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2 [ 5.915673] ohci-platform ohci-platform: irq 14, io mem 0x1c000000 [ 5.995228] hub 2-0:1.0: USB hub found [ 5.999267] hub 2-0:1.0: 2 ports detected [ 6.004254] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 6.021937] init: - preinit - [ 6.710149] ar71xx: pll_reg 0xb8050010: 0x11110000 [ 6.710168] eth0: link up (1000Mbps/Full duplex) [ 6.736457] random: procd: uninitialized urandom read (4 bytes read) [ 9.958061] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000 [ 9.965304] jffs2_build_filesystem(): unlocking the mtd device... [ 9.965309] done. [ 9.973395] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 20.815192] done. [ 20.824637] jffs2: notice: (510) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 20.844266] mount_root: overlay filesystem has not been fully initialized yet [ 20.858620] mount_root: switching to jffs2 overlay [ 20.896683] overlayfs: upper fs does not support tmpfile. [ 21.751888] urandom-seed: Seed file not found (/etc/urandom.seed) [ 21.916613] eth0: link down [ 21.929795] procd: - early - [ 21.933421] procd: - watchdog - [ 22.560619] procd: - watchdog - [ 22.564060] procd: - ubus - [ 22.667832] random: ubusd: uninitialized urandom read (4 bytes read) [ 22.675169] random: ubusd: uninitialized urandom read (4 bytes read) [ 22.681980] random: ubusd: uninitialized urandom read (4 bytes read) [ 22.689163] procd: - init - [ 23.328070] kmodloader: loading kernel modules from /etc/modules.d/* [ 23.356086] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 23.378844] Loading modules backported from Linux version v4.19.137-0-gc076c79e03c6 [ 23.386549] Backport generated by backports.git v4.19.137-1-0-g60c3a249 [ 23.412616] ip_tables: (C) 2000-2006 Netfilter Core Team [ 23.437348] nf_conntrack version 0.5.0 (1024 buckets, 4096 max) [ 23.542215] xt_time: kernel timezone is -0000 [ 23.634978] PPP generic driver version 2.4.2 [ 23.651342] NET: Registered protocol family 24 [ 23.701444] pci 0000:00:11.0: using irq 40 for pin 1 [ 23.706417] PCI: Enabling device 0000:00:11.0 (0000 -> 0002) [ 23.716959] ath: phy0: Ignoring endianness difference in EEPROM magic bytes. [ 23.725564] ath: EEPROM regdomain: 0x0 [ 23.725568] ath: EEPROM indicates default country code should be used [ 23.725571] ath: doing EEPROM country->regdmn map search [ 23.725582] ath: country maps to regdmn code: 0x3a [ 23.725587] ath: Country alpha2 being used: US [ 23.725590] ath: Regpair used: 0x3a [ 23.740046] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 23.741784] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=40 [ 23.748474] pci 0000:00:12.0: using irq 41 for pin 1 [ 23.753502] PCI: Enabling device 0000:00:12.0 (0000 -> 0002) [ 23.763987] ath: phy1: Ignoring endianness difference in EEPROM magic bytes. [ 23.772567] ath: EEPROM regdomain: 0x0 [ 23.772572] ath: EEPROM indicates default country code should be used [ 23.772575] ath: doing EEPROM country->regdmn map search [ 23.772585] ath: country maps to regdmn code: 0x3a [ 23.772590] ath: Country alpha2 being used: US [ 23.772593] ath: Regpair used: 0x3a [ 23.789243] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht' [ 23.790960] ieee80211 phy1: Atheros AR9280 Rev:2 mem=0xb0010000, irq=41 [ 23.926005] urngd: v1.0.2 started. [ 24.015339] kmodloader: done loading kernel modules from /etc/modules.d/* [ 24.402291] random: crng init done [ 24.405700] random: 6 urandom warning(s) missed due to ratelimiting [ 31.380568] rtl8366s rtl8366s: applying initvals [ 36.313241] ar71xx: pll_reg 0xb8050010: 0x11110000 [ 36.318125] eth0: link up (1000Mbps/Full duplex) [ 36.322896] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 36.379013] br-lan: port 1(eth0.1) entered blocking state [ 36.384474] br-lan: port 1(eth0.1) entered disabled state [ 36.390156] device eth0.1 entered promiscuous mode [ 36.394989] device eth0 entered promiscuous mode [ 36.470707] br-lan: port 1(eth0.1) entered blocking state [ 36.476113] br-lan: port 1(eth0.1) entered forwarding state [ 36.481893] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 36.550031] br-lan: port 2(eth1) entered blocking state [ 36.555322] br-lan: port 2(eth1) entered disabled state [ 36.560829] device eth1 entered promiscuous mode [ 37.414242] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 37.421244] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 38.240837] ath: EEPROM regdomain: 0x826c [ 38.244846] ath: EEPROM indicates we should expect a country code [ 38.250975] ath: doing EEPROM country->regdmn map search [ 38.256274] ath: country maps to regdmn code: 0x37 [ 38.261069] ath: Country alpha2 being used: PT [ 38.265495] ath: Regpair used: 0x37 [ 38.268978] ath: regdomain 0x826c dynamically updated by user [ 38.274840] ath: EEPROM regdomain: 0x826c [ 38.278837] ath: EEPROM indicates we should expect a country code [ 38.284927] ath: doing EEPROM country->regdmn map search [ 38.290226] ath: country maps to regdmn code: 0x37 [ 38.295017] ath: Country alpha2 being used: PT [ 38.299445] ath: Regpair used: 0x37 [ 38.302928] ath: regdomain 0x826c dynamically updated by user [ 39.934879] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready [ 39.973271] br-lan: port 3(wlan1) entered blocking state [ 39.978589] br-lan: port 3(wlan1) entered disabled state [ 39.984241] device wlan1 entered promiscuous mode [ 40.041321] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 40.100323] br-lan: port 4(wlan0) entered blocking state [ 40.105700] br-lan: port 4(wlan0) entered disabled state [ 40.111300] device wlan0 entered promiscuous mode [ 40.116082] br-lan: port 4(wlan0) entered blocking state [ 40.121436] br-lan: port 4(wlan0) entered forwarding state [ 40.721813] ar71xx: pll_reg 0xb8050014: 0x11110000 [ 40.726609] eth1: link up (1000Mbps/Full duplex) [ 40.740573] br-lan: port 2(eth1) entered blocking state [ 40.745797] br-lan: port 2(eth1) entered forwarding state [ 40.779728] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready [ 40.786320] br-lan: port 3(wlan1) entered blocking state [ 40.791663] br-lan: port 3(wlan1) entered forwarding state [ 40.950566] br-lan: port 4(wlan0) entered disabled state [ 42.190116] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 42.196770] br-lan: port 4(wlan0) entered blocking state [ 42.202125] br-lan: port 4(wlan0) entered forwarding state [28859.481593] rtl8366s rtl8366s: applying initvals [28859.504703] br-lan: port 5(eth0) entered blocking state [28859.509985] br-lan: port 5(eth0) entered disabled state [28859.615684] br-lan: port 5(eth0) entered blocking state [28859.621076] br-lan: port 5(eth0) entered disabled state [28859.781577] rtl8366s rtl8366s: applying initvals [29636.826087] rtl8366s rtl8366s: applying initvals [29636.849406] device eth0.1 left promiscuous mode [29636.853994] device eth0 left promiscuous mode [29636.858557] br-lan: port 1(eth0.1) entered disabled state [29636.866668] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready [29636.875798] eth0: link down [29636.888370] ar71xx: pll_reg 0xb8050010: 0x11110000 [29636.893234] eth0: link up (1000Mbps/Full duplex) [29636.913676] br-lan: port 1(eth0.1) entered blocking state [29636.919225] br-lan: port 1(eth0.1) entered disabled state [29636.924915] device eth0.1 entered promiscuous mode [29636.929773] device eth0 entered promiscuous mode [29636.934616] br-lan: port 1(eth0.1) entered blocking state [29636.940058] br-lan: port 1(eth0.1) entered forwarding state [29637.296052] rtl8366s rtl8366s: applying initvals