DDR Version V1.13 20220218 ln ddrconfig:0 LPDDR4X, 324MHz BW=32 Col=10 Bk=8 CS0 Row=17 CS=1 Die BW=16 Size=4096MB tdqss: cs0 dqs0: 24ps, dqs1: -72ps, dqs2: -24ps, dqs3: -72ps, change to: 324MHz PHY drv:clk:36,ca:36,DQ:29,odt:0 vrefinner:24%, vrefout:41% dram drv:40,odt:0 clk skew:0x60 change to: 528MHz PHY drv:clk:36,ca:36,DQ:29,odt:0 vrefinner:24%, vrefout:41% dram drv:40,odt:0 clk skew:0x58 change to: 780MHz PHY drv:clk:36,ca:36,DQ:29,odt:0 vrefinner:24%, vrefout:41% dram drv:40,odt:0 clk skew:0x58 change to: 1560MHz(final freq) PHY drv:clk:36,ca:36,DQ:29,odt:60 vrefinner:16%, vrefout:22% dram drv:40,odt:80 vref_ca:00000071 clk skew:0x12 cs 0: the read training result: DQS0:0x32, DQS1:0x31, DQS2:0x35, DQS3:0x2e, min :0x10 0xf 0x7 0x3 0x7 0x7 0xe 0xb , 0x6 0x0 0x1 0x2 0x7 0xd 0x12 0xc , 0xd 0xb 0xb 0x9 0x7 0x2 0x9 0x9 , 0x1 0x2 0x7 0x0 0x9 0x5 0x3 0x2 , mid :0x29 0x2a 0x21 0x1e 0x20 0x21 0x27 0x26 ,0x1f 0x1b 0x1b 0x1d 0x21 0x29 0x2c 0x27 , 0x27 0x26 0x26 0x24 0x22 0x1e 0x24 0x24 ,0x1c 0x1c 0x22 0x1b 0x24 0x21 0x1e 0x1d , max :0x42 0x45 0x3b 0x39 0x3a 0x3c 0x41 0x42 ,0x39 0x37 0x35 0x39 0x3b 0x46 0x46 0x42 , 0x42 0x42 0x42 0x40 0x3e 0x3a 0x40 0x3f ,0x37 0x37 0x3d 0x37 0x3f 0x3e 0x39 0x39 , range:0x32 0x36 0x34 0x36 0x33 0x35 0x33 0x37 ,0x33 0x37 0x34 0x37 0x34 0x39 0x34 0x36 , 0x35 0x37 0x37 0x37 0x37 0x38 0x37 0x36 ,0x36 0x35 0x36 0x37 0x36 0x39 0x36 0x37 , the write training result: DQS0:0x16, DQS1:0x4, DQS2:0xe, DQS3:0x4, min :0x65 0x69 0x60 0x5c 0x5e 0x5e 0x65 0x67 0x6a ,0x4b 0x48 0x47 0x49 0x4e 0x54 0x56 0x54 0x4d , 0x53 0x53 0x53 0x52 0x4d 0x4a 0x4e 0x51 0x51 ,0x43 0x44 0x4b 0x45 0x4b 0x49 0x47 0x48 0x49 , mid :0x80 0x82 0x7a 0x76 0x78 0x78 0x7f 0x80 0x83 ,0x67 0x62 0x61 0x62 0x69 0x6f 0x70 0x6e 0x68 , 0x6f 0x6f 0x6e 0x6e 0x69 0x63 0x69 0x6b 0x6c ,0x5d 0x5f 0x66 0x60 0x67 0x63 0x60 0x62 0x62 , max :0x9b 0x9c 0x95 0x91 0x93 0x93 0x99 0x9a 0x9c ,0x83 0x7c 0x7b 0x7c 0x84 0x8a 0x8a 0x88 0x84 , 0x8c 0x8c 0x89 0x8a 0x86 0x7c 0x84 0x86 0x88 ,0x77 0x7a 0x82 0x7c 0x83 0x7e 0x7a 0x7c 0x7c , range:0x36 0x33 0x35 0x35 0x35 0x35 0x34 0x33 0x32 ,0x38 0x34 0x34 0x33 0x36 0x36 0x34 0x34 0x37 , 0x39 0x39 0x36 0x38 0x39 0x32 0x36 0x35 0x37 ,0x34 0x36 0x37 0x37 0x38 0x35 0x33 0x34 0x33 , CA Training result: cs:0 min :0x3a 0x38 0x32 0x32 0x38 0x2d 0x38 ,0x3d 0x36 0x38 0x32 0x38 0x2f 0x3b , cs:0 mid :0x77 0x7a 0x6e 0x74 0x73 0x6e 0x64 ,0x79 0x75 0x76 0x72 0x74 0x6e 0x68 , cs:0 max :0xb5 0xbc 0xab 0xb6 0xae 0xaf 0x91 ,0xb5 0xb5 0xb4 0xb3 0xb1 0xae 0x95 , cs:0 range:0x7b 0x84 0x79 0x84 0x76 0x82 0x59 ,0x78 0x7f 0x7c 0x81 0x79 0x7f 0x5a , out rockchip_sdram_size fdc20208 10000201 rank 1 cs0_col 10 bk 3 cs0_row 17 bw 2 row_3_4 0 SDRAM base=0, size=100000000 U-Boot SPL 2022.04-rc2 (Nov 09 2022 - 00:02:16 +0000) saradc@fe720000: Can't update Vdd. Error: -38saradc@fe720000: Can't update Vss. Error: -38powerdomain init. rockchip_sdhci_probe clk set rate fail! Trying to boot from MMC2 INFO: Preloader serial: 2 NOTICE: BL31: v2.3():v2.3-152-g4e725b15f:cl NOTICE: BL31: Built : 10:51:13, Jul 15 2021 INFO: GICv3 without legacy support detected. INFO: ARM GICv3 driver initialized in EL3 INFO: pmu v1 is valid INFO: dfs DDR fsp_param[0].freq_mhz= 1560MHz INFO: dfs DDR fsp_param[1].freq_mhz= 324MHz INFO: dfs DDR fsp_param[2].freq_mhz= 528MHz INFO: dfs DDR fsp_param[3].freq_mhz= 780MHz INFO: Using opteed sec cpu_context! INFO: boot cpu mask: 0 INFO: BL31: Initializing runtime services WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK ERROR: Error initializing runtime service opteed_fast INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0xa00000 INFO: SPSR = 0x3c9 U-Boot 2022.04-rc2 (Nov 09 2022 - 00:02:16 +0000) Model: Pine64 RK3566 SoQuartz with CM4-IO Carrier Board DRAM: rockchip_sdram_size fdc20208 10000201 rank 1 cs0_col 10 bk 3 cs0_row 17 bw 2 row_3_4 0 SDRAM base=0, size=100000000 3.7 GiB PMIC: RK8090 (on=0x10, off=0x00) Core: 289 devices, 18 uclasses, devicetree: separate MMC: rockchip_sdhci_probe clk set rate fail! mmc@fe2b0000: 1, mmc@fe2c0000: 2, mmc@fe310000: 0 Loading Environment from nowhere... OK In: serial@fe660000 Out: serial@fe660000 Err: serial@fe660000 Model: Pine64 RK3566 SoQuartz with CM4-IO Carrier Board Net: No ethernet found. Hit any key to stop autoboot: 0 Card did not respond to voltage select! : -110 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 1: Boot primary OS Retrieving file: /boot/vmlinuz append: earlycon=uart8250,mmio32,0xfe660000 console=ttyS2,1500000n8 console=tty1 root=PARTUUID=f7e6c25f-01 rootfstype=ext4 rootwait fsck.repair=yes net.ifnames=0 systemd.unified_cgroup_hierarchy=0 Retrieving file: /boot/rk3566-soquartz-cm4.dtb Moving Image from 0x2080000 to 0x2200000, end=45b0000 ## Flattened Device Tree blob at 0a100000 Booting using the fdt blob at 0xa100000 Loading Device Tree to 00000000ededa000, end 00000000edee9f09 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050] [ 0.000000] Linux version 6.1.0-rc1 (root@runner-7gzwldlw-project-27231216-concurrent-0) (aarch64-none-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16)) 10.2.1 20201103, GNU ld (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16)) 2.35.1.20201028) #1 SMP PREEMPT Wed Nov 9 01:08:14 UTC 2022 [ 0.000000] Machine model: Pine64 RK3566 SoQuartz with CM4-IO Carrier Board [ 0.000000] earlycon: uart8250 at MMIO32 0x00000000fe660000 (options '') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] efi: UEFI not found. [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000000200000-0x00000000efffffff] [ 0.000000] NUMA: NODE_DATA [mem 0xef829a00-0xef82bfff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000200000-0x00000000efffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000200000-0x00000000efffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000200000-0x00000000efffffff] [ 0.000000] On node 0, zone DMA: 512 pages in unavailable ranges [ 0.000000] cma: Reserved 32 MiB at 0x00000000e8200000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 28 pages/cpu s75688 r8192 d30808 u114688 [ 0.000000] pcpu-alloc: s75688 r8192 d30808 u114688 alloc=28*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Virtualization Host Extensions [ 0.000000] CPU features: detected: Qualcomm erratum 1009, or ARM erratum 1286807, 2441009 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Fallback order for Node 0: 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 967176 [ 0.000000] Policy zone: DMA [ 0.000000] Kernel command line: earlycon=uart8250,mmio32,0xfe660000 console=ttyS2,1500000n8 console=tty1 root=PARTUUID=f7e6c25f-01 rootfstype=ext4 rootwait fsck.repair=yes net.ifnames=0 systemd.unified_cgroup_hierarchy=0 [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 3784684K/3930112K available (19136K kernel code, 3158K rwdata, 6976K rodata, 6400K init, 702K bss, 112660K reserved, 32768K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] ftrace: allocating 60326 entries in 236 pages [ 0.000000] ftrace: allocated 236 pages with 5 groups [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 320 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: MBI range [296:319] [ 0.000000] GICv3: Using MBI frame 0x00000000fd410000 [ 0.000000] Root IRQ handler: gic_handle_irq [ 0.000000] GICv3: GICv3 features: 16 PPIs [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000fd460000 [ 0.000000] ITS: No ITS available, not enabling LPIs [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.001528] Console: colour dummy device 80x25 [ 0.001987] printk: console [tty1] enabled [ 0.002465] printk: bootconsole [uart8250] disabled [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050] [ 0.000000] Linux version 6.1.0-rc1 (root@runner-7gzwldlw-project-27231216-concurrent-0) (aarch64-none-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16)) 10.2.1 20201103, GNU ld (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16)) 2.35.1.20201028) #1 SMP PREEMPT Wed Nov 9 01:08:14 UTC 2022 [ 0.000000] Machine model: Pine64 RK3566 SoQuartz with CM4-IO Carrier Board [ 0.000000] earlycon: uart8250 at MMIO32 0x00000000fe660000 (options '') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] efi: UEFI not found. [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000000200000-0x00000000efffffff] [ 0.000000] NUMA: NODE_DATA [mem 0xef829a00-0xef82bfff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000200000-0x00000000efffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000200000-0x00000000efffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000200000-0x00000000efffffff] [ 0.000000] On node 0, zone DMA: 512 pages in unavailable ranges [ 0.000000] cma: Reserved 32 MiB at 0x00000000e8200000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 28 pages/cpu s75688 r8192 d30808 u114688 [ 0.000000] pcpu-alloc: s75688 r8192 d30808 u114688 alloc=28*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Virtualization Host Extensions [ 0.000000] CPU features: detected: Qualcomm erratum 1009, or ARM erratum 1286807, 2441009 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Fallback order for Node 0: 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 967176 [ 0.000000] Policy zone: DMA [ 0.000000] Kernel command line: earlycon=uart8250,mmio32,0xfe660000 console=ttyS2,1500000n8 console=tty1 root=PARTUUID=f7e6c25f-01 rootfstype=ext4 rootwait fsck.repair=yes net.ifnames=0 systemd.unified_cgroup_hierarchy=0 [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 3784684K/3930112K available (19136K kernel code, 3158K rwdata, 6976K rodata, 6400K init, 702K bss, 112660K reserved, 32768K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] ftrace: allocating 60326 entries in 236 pages [ 0.000000] ftrace: allocated 236 pages with 5 groups [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 320 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: MBI range [296:319] [ 0.000000] GICv3: Using MBI frame 0x00000000fd410000 [ 0.000000] Root IRQ handler: gic_handle_irq [ 0.000000] GICv3: GICv3 features: 16 PPIs [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000fd460000 [ 0.000000] ITS: No ITS available, not enabling LPIs [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.001528] Console: colour dummy device 80x25 [ 0.001987] printk: console [tty1] enabled [ 0.002465] printk: bootconsole [uart8250] disabled [ 0.003065] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.003104] pid_max: default: 32768 minimum: 301 [ 0.003217] LSM: Security Framework initializing [ 0.003391] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.003443] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.004899] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.006157] cblist_init_generic: Setting adjustable number of callback queues. [ 0.006191] cblist_init_generic: Setting shift to 2 and lim to 1. [ 0.006365] cblist_init_generic: Setting shift to 2 and lim to 1. [ 0.006816] rcu: Hierarchical SRCU implementation. [ 0.006839] rcu: Max phase no-delay instances is 1000. [ 0.007733] EFI services will not be available. [ 0.008449] smp: Bringing up secondary CPUs ... [ 0.009452] Detected VIPT I-cache on CPU1 [ 0.009574] cacheinfo: Unable to detect cache hierarchy for CPU 1 [ 0.009592] GICv3: CPU1: found redistributor 100 region 0:0x00000000fd480000 [ 0.009655] CPU1: Booted secondary processor 0x0000000100 [0x412fd050] [ 0.010871] Detected VIPT I-cache on CPU2 [ 0.010970] cacheinfo: Unable to detect cache hierarchy for CPU 2 [ 0.010988] GICv3: CPU2: found redistributor 200 region 0:0x00000000fd4a0000 [ 0.011035] CPU2: Booted secondary processor 0x0000000200 [0x412fd050] [ 0.012095] Detected VIPT I-cache on CPU3 [ 0.012196] cacheinfo: Unable to detect cache hierarchy for CPU 3 [ 0.012216] GICv3: CPU3: found redistributor 300 region 0:0x00000000fd4c0000 [ 0.012261] CPU3: Booted secondary processor 0x0000000300 [0x412fd050] [ 0.012425] smp: Brought up 1 node, 4 CPUs [ 0.012592] SMP: Total of 4 processors activated. [ 0.012612] CPU features: detected: 32-bit EL0 Support [ 0.012630] CPU features: detected: 32-bit EL1 Support [ 0.012649] CPU features: detected: Data cache clean to the PoU not required for I/D coherence [ 0.012672] CPU features: detected: Common not Private translations [ 0.012690] CPU features: detected: CRC32 instructions [ 0.012710] CPU features: detected: RCpc load-acquire (LDAPR) [ 0.012726] CPU features: detected: LSE atomic instructions [ 0.012744] CPU features: detected: Privileged Access Never [ 0.012760] CPU features: detected: RAS Extension Support [ 0.012781] CPU features: detected: Speculative Store Bypassing Safe (SSBS) [ 0.012905] CPU: All CPU(s) started at EL2 [ 0.012928] alternatives: applying system-wide alternatives [ 0.019542] devtmpfs: initialized [ 0.036790] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.036860] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.038205] pinctrl core: initialized pinctrl subsystem [ 0.038765] regulator-dummy: no parameters, enabled [ 0.039344] DMI not present or invalid. [ 0.040242] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.042137] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations [ 0.042428] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.042818] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 [ 0.406165] brd: module loaded [ 0.415971] loop: module loaded [ 0.417115] zram: Added device: zram0 [ 0.417763] megasas: 07.719.03.00-rc1 [ 0.428306] tun: Universal TUN/TAP device driver, 1.6 [ 0.429187] e100: Intel(R) PRO/100 Network Driver [ 0.429629] e100: Copyright(c) 1999-2006 Intel Corporation [ 0.430215] e1000: Intel(R) PRO/1000 Network Driver [ 0.430668] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 0.431321] e1000e: Intel(R) PRO/1000 Network Driver [ 0.431781] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.432388] igb: Intel(R) Gigabit Ethernet Network Driver [ 0.432886] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.433457] Intel(R) 2.5G Ethernet Linux Driver [ 0.433876] Copyright(c) 2018 Intel Corporation. [ 0.434366] igbvf: Intel(R) Gigabit Virtual Function Network Driver [ 0.434961] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.435565] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver [ 0.436122] ixgbe: Copyright (c) 1999-2016 Intel Corporation. [ 0.437025] ixgbevf: Intel(R) 10 Gigabit PCI Express Virtual Function Network Driver [ 0.437730] ixgbevf: Copyright (c) 2009 - 2018 Intel Corporation. [ 0.438535] i40e: Intel(R) Ethernet Connection XL710 Network Driver [ 0.439151] i40e: Copyright (c) 2013 - 2019 Intel Corporation. [ 0.439968] ixgb: Intel(R) PRO/10GbE Network Driver [ 0.440422] ixgb: Copyright (c) 1999-2008 Intel Corporation. [ 0.441012] iavf: Intel(R) Ethernet Adaptive Virtual Function Network Driver [ 0.441653] Copyright (c) 2013 - 2018 Intel Corporation. [ 0.442406] Intel(R) Ethernet Switch Host Interface Driver [ 0.442947] Copyright(c) 2013 - 2019 Intel Corporation. [ 0.443716] ice: Intel(R) Ethernet Connection E800 Series Linux Driver [ 0.444315] ice: Copyright (c) 2018, Intel Corporation. [ 0.446781] usbcore: registered new interface driver rtl8192cu [ 0.447881] usbcore: registered new interface driver rtl8xxxu [ 0.448703] usbcore: registered new interface driver ax88179_178a [ 0.449629] VFIO - User Level meta-driver version: 0.3 [ 0.457117] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 0.457671] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 0.458547] xhci-hcd xhci-hcd.0.auto: USB3 root hub has no ports [ 0.459143] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000002002010010 [ 0.460090] xhci-hcd xhci-hcd.0.auto: irq 33, io mem 0xfcc00000 [ 0.462054] hub 1-0:1.0: USB hub found [ 0.462461] hub 1-0:1.0: 1 port detected [ 0.463601] usbcore: registered new interface driver usb-storage [ 0.465852] i2c_dev: i2c /dev entries driver [ 0.474710] rtc rtc0: Power loss detected, invalid time [ 0.475530] rtc-pcf85063 1-0051: registered as rtc0 [ 0.477022] rtc rtc0: Power loss detected, invalid time [ 0.477509] rtc-pcf85063 1-0051: hctosys: unable to read the hardware clock [ 0.479326] arm-scmi firmware:scmi: Failed. SCMI protocol 21 not active. [ 0.481963] rockchip-thermal fe710000.tsadc: Missing tshut mode property, using default (gpio) [ 0.482788] rockchip-thermal fe710000.tsadc: Missing tshut-polarity property, using default (low) [ 0.486958] cpu cpu0: Looking up cpu-supply from device tree [ 0.487763] arm-scmi firmware:scmi: Failed. SCMI protocol 19 not active. [ 0.489853] sdhci: Secure Digital Host Controller Interface driver [ 0.490425] sdhci: Copyright(c) Pierre Ossman [ 0.491302] Synopsys Designware Multimedia Card Interface Driver [ 0.492386] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.495502] ledtrig-cpu: registered to indicate activity on CPUs [ 0.496890] arm-scmi firmware:scmi: Failed. SCMI protocol 17 not active. [ 0.497601] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 0.498822] usbcore: registered new interface driver usbhid [ 0.499340] usbhid: USB HID core driver [ 0.500968] SPI driver st-accel-spi has no spi_device_id for st,lis302dl-spi [ 0.501616] SPI driver st-accel-spi has no spi_device_id for st,lis3lv02dl-accel [ 0.502286] SPI driver st-accel-spi has no spi_device_id for st,lis3dh-accel [ 0.502961] SPI driver st-accel-spi has no spi_device_id for st,lsm330d-accel [ 0.503609] SPI driver st-accel-spi has no spi_device_id for st,lsm330dl-accel [ 0.504262] SPI driver st-accel-spi has no spi_device_id for st,lsm330dlc-accel [ 0.504921] SPI driver st-accel-spi has no spi_device_id for st,lis331dlh-accel [ 0.505579] SPI driver st-accel-spi has no spi_device_id for st,lsm330-accel [ 0.506212] SPI driver st-accel-spi has no spi_device_id for st,lsm303agr-accel [ 0.506890] SPI driver st-accel-spi has no spi_device_id for st,lis2dh12-accel [ 0.507547] SPI driver st-accel-spi has no spi_device_id for st,lng2dm-accel [ 0.508183] SPI driver st-accel-spi has no spi_device_id for st,h3lis331dl-accel [ 0.508851] SPI driver st-accel-spi has no spi_device_id for st,lis331dl-accel [ 0.518221] NET: Registered PF_PACKET protocol family [ 0.518977] 9pnet: Installing 9P2000 support [ 0.519475] Key type dns_resolver registered [ 0.520617] registered taskstats version 1 [ 0.521018] Loading compiled-in X.509 certificates [ 0.525697] zswap: loaded using pool zstd/zsmalloc [ 0.596074] reg-fixed-voltage vbus-regulator: Looking up vin-supply from device tree [ 0.596831] vbus: supplied by vcc_5v [ 0.597173] vcc_5v: could not add device link regulator.4: -ENOENT [ 0.597821] vbus: 5000 mV, enabled [ 0.598382] reg-fixed-voltage vbus-regulator: vbus supplying 5000000uV [ 0.599348] reg-fixed-voltage vcc5v0-sys-regulator: Looking up vin-supply from device tree [ 0.600114] vcc5v0_sys: supplied by vbus [ 0.600485] vbus: could not add device link regulator.5: -ENOENT [ 0.601128] vcc5v0_sys: 5000 mV, enabled [ 0.601699] reg-fixed-voltage vcc5v0-sys-regulator: vcc5v0_sys supplying 5000000uV [ 0.602676] reg-fixed-voltage vcc3v3-sys-regulator: Looking up vin-supply from device tree [ 0.603472] vcc3v3_sys: supplied by vcc5v0_sys [ 0.603893] vcc5v0_sys: could not add device link regulator.6: -ENOENT [ 0.604553] vcc3v3_sys: 3300 mV, enabled [ 0.605103] reg-fixed-voltage vcc3v3-sys-regulator: vcc3v3_sys supplying 3300000uV [ 0.607758] fan53555-regulator 0-001c: FAN53555 Option[12] Rev[15] Detected! [ 0.608425] fan53555-regulator 0-001c: Looking up vin-supply from device tree [ 0.609088] vdd_cpu: supplied by vcc5v0_sys [ 0.609513] vcc5v0_sys: could not add device link regulator.7: -ENOENT [ 0.613124] vdd_cpu: 800 <--> 1150 mV at 900 mV, enabled [ 0.616075] rk808 0-0020: chip id: 0x8090 [ 0.662588] rk808-regulator rk808-regulator: there is no dvs0 gpio [ 0.663252] rk808-regulator rk808-regulator: there is no dvs1 gpio [ 0.663954] rk808 0-0020: Looking up vcc1-supply from device tree [ 0.664661] vdd_logic: supplied by vcc3v3_sys [ 0.665075] vcc3v3_sys: could not add device link regulator.8: -ENOENT [ 0.670055] vdd_logic: 500 <--> 1350 mV at 900 mV, enabled [ 0.671419] rk808 0-0020: Looking up vcc2-supply from device tree [ 0.671995] vdd_gpu: supplied by vcc3v3_sys [ 0.672391] vcc3v3_sys: could not add device link regulator.9: -ENOENT [ 0.676810] vdd_gpu: 500 <--> 1350 mV at 900 mV, enabled [ 0.678114] rk808 0-0020: Looking up vcc3-supply from device tree [ 0.678690] vcc_ddr: supplied by vcc3v3_sys [ 0.679120] vcc3v3_sys: could not add device link regulator.10: -ENOENT [ 0.682574] vcc_ddr: at 500 mV, enabled [ 0.683800] rk808 0-0020: Looking up vcc4-supply from device tree [ 0.684375] vdd_npu: supplied by vcc3v3_sys [ 0.684770] vcc3v3_sys: could not add device link regulator.11: -ENOENT [ 0.688711] vdd_npu: 500 <--> 1350 mV at 900 mV, enabled [ 0.690020] rk808 0-0020: Looking up vcc9-supply from device tree [ 0.690595] vcc_1v8: supplied by vcc3v3_sys [ 0.691023] vcc3v3_sys: could not add device link regulator.12: -ENOENT [ 0.694493] vcc_1v8: 1800 mV, enabled [ 0.695668] rk808 0-0020: Looking up vcc5-supply from device tree [ 0.696243] vdda0v9_image: supplied by vcc3v3_sys [ 0.696682] vcc3v3_sys: could not add device link regulator.13: -ENOENT [ 0.700670] vdda0v9_image: 900 mV, enabled [ 0.701878] rk808 0-0020: Looking up vcc5-supply from device tree [ 0.702453] vdda_0v9: supplied by vcc3v3_sys [ 0.702888] vcc3v3_sys: could not add device link regulator.14: -ENOENT [ 0.706401] vdda_0v9: 900 mV, enabled [ 0.707585] rk808 0-0020: Looking up vcc5-supply from device tree [ 0.708160] vdda0v9_pmu: supplied by vcc3v3_sys [ 0.708586] vcc3v3_sys: could not add device link regulator.15: -ENOENT [ 0.712577] vdda0v9_pmu: 900 mV, enabled [ 0.713759] rk808 0-0020: Looking up vcc6-supply from device tree [ 0.714333] vccio_acodec: supplied by vcc3v3_sys [ 0.714802] vcc3v3_sys: could not add device link regulator.16: -ENOENT [ 0.718302] vccio_acodec: 3300 mV, enabled [ 0.718798] usb 1-1: new high-speed USB device number 2 using xhci-hcd [ 0.719548] rk808 0-0020: Looking up vcc6-supply from device tree [ 0.720126] vccio_sd: supplied by vcc3v3_sys [ 0.720526] vcc3v3_sys: could not add device link regulator.17: -ENOENT [ 0.724515] vccio_sd: 1800 <--> 3300 mV at 3300 mV, enabled [ 0.725844] rk808 0-0020: Looking up vcc6-supply from device tree [ 0.726420] vcc3v3_pmu: supplied by vcc3v3_sys [ 0.726869] vcc3v3_sys: could not add device link regulator.18: -ENOENT [ 0.730853] vcc3v3_pmu: 3300 mV, enabled [ 0.732040] rk808 0-0020: Looking up vcc7-supply from device tree [ 0.732616] vcca_1v8: supplied by vcc3v3_sys [ 0.733014] vcc3v3_sys: could not add device link regulator.19: -ENOENT [ 0.736541] vcca_1v8: 1800 mV, enabled [ 0.737724] rk808 0-0020: Looking up vcc7-supply from device tree [ 0.738301] vcca1v8_pmu: supplied by vcc3v3_sys [ 0.738726] vcc3v3_sys: could not add device link regulator.20: -ENOENT [ 0.742263] vcca1v8_pmu: 1800 mV, enabled [ 0.743463] rk808 0-0020: Looking up vcc7-supply from device tree [ 0.744038] vcca1v8_image: supplied by vcc3v3_sys [ 0.744478] vcc3v3_sys: could not add device link regulator.21: -ENOENT [ 0.747989] vcca1v8_image: 1800 mV, enabled [ 0.750167] vcc_3v3: no parameters, enabled [ 0.750822] rk808 0-0020: Looking up vcc9-supply from device tree [ 0.751398] vcc_3v3: supplied by vcc3v3_sys [ 0.752397] SWITCH_REG2: no parameters, enabled [ 0.752999] rk808 0-0020: Looking up vcc8-supply from device tree [ 0.753573] SWITCH_REG2: supplied by vcc3v3_sys [ 0.760574] input: rk805 pwrkey as /devices/platform/fdd40000.i2c/i2c-0/0-0020/rk805-pwrkey/input/input0 [ 0.774049] rk808-rtc rk808-rtc: registered as rtc1 [ 0.775704] cpu cpu0: Looking up cpu-supply from device tree [ 0.783144] rockchip-iodomain fdc20000.syscon:io-domains: Looking up pmuio1-supply from device tree [ 0.783465] dwmmc_rockchip fe2b0000.mmc: IDMAC supports 32-bit address mode. [ 0.783932] dwmmc_rockchip fe2c0000.mmc: IDMAC supports 32-bit address mode. [ 0.783955] dwmmc_rockchip fe2c0000.mmc: Using internal DMA controller. [ 0.783962] dwmmc_rockchip fe2c0000.mmc: Version ID is 270a [ 0.784013] dwmmc_rockchip fe2c0000.mmc: DW MMC controller at irq 64,32 bit host data width,256 deep fifo [ 0.784608] dwmmc_rockchip fe2b0000.mmc: Using internal DMA controller. [ 0.784693] dwmmc_rockchip fe2c0000.mmc: Looking up vmmc-supply from device tree [ 0.785236] dwmmc_rockchip fe2b0000.mmc: Version ID is 270a [ 0.785274] dwmmc_rockchip fe2b0000.mmc: DW MMC controller at irq 63,32 bit host data width,256 deep fifo [ 0.786412] dwmmc_rockchip fe2c0000.mmc: Looking up vqmmc-supply from device tree [ 0.786550] sdhci-dwcmshc fe310000.mmc: Looking up vmmc-supply from device tree [ 0.786657] sdhci-dwcmshc fe310000.mmc: Looking up vqmmc-supply from device tree [ 0.787313] dwmmc_rockchip fe2b0000.mmc: Looking up vmmc-supply from device tree [ 0.787856] rockchip-iodomain fdc20000.syscon:io-domains: Looking up pmuio2-supply from device tree [ 0.788518] dwmmc_rockchip fe2b0000.mmc: Looking up vqmmc-supply from device tree [ 0.789150] dwmmc_rockchip fe2c0000.mmc: allocated mmc-pwrseq [ 0.792463] sdhci-dwcmshc fe310000.mmc: Disabling HS200/HS400, frequency too low (50000000) [ 0.793239] mmc_host mmc2: card is non-removable. [ 0.794027] mmc_host mmc0: card is polling. [ 0.797193] rockchip-iodomain fdc20000.syscon:io-domains: Looking up vccio1-supply from device tree [ 0.800006] rockchip-iodomain fdc20000.syscon:io-domains: Looking up vccio2-supply from device tree [ 0.801850] rockchip-iodomain fdc20000.syscon:io-domains: Looking up vccio3-supply from device tree [ 0.803679] rockchip-iodomain fdc20000.syscon:io-domains: Looking up vccio4-supply from device tree [ 0.805456] rockchip-iodomain fdc20000.syscon:io-domains: Looking up vccio5-supply from device tree [ 0.806307] rockchip-iodomain fdc20000.syscon:io-domains: Looking up vccio6-supply from device tree [ 0.807181] rockchip-iodomain fdc20000.syscon:io-domains: Looking up vccio7-supply from device tree [ 0.808940] rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found [ 0.809639] rk_gmac-dwmac fe010000.ethernet: Looking up phy-supply from device tree [ 0.810420] rk_gmac-dwmac fe010000.ethernet: clock input or output? (input). [ 0.811136] mmc_host mmc2: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0) [ 0.811555] mmc_host mmc0: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0) [ 0.812006] rk_gmac-dwmac fe010000.ethernet: TX delay(0x30). [ 0.813264] rk_gmac-dwmac fe010000.ethernet: RX delay(0x10). [ 0.813773] rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no). [ 0.814357] rk_gmac-dwmac fe010000.ethernet: clock input from PHY [ 0.819931] rk_gmac-dwmac fe010000.ethernet: init for RGMII [ 0.820652] rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51 [ 0.821292] rk_gmac-dwmac fe010000.ethernet: DWMAC4/5 [ 0.821753] rk_gmac-dwmac fe010000.ethernet: DMA HW capability register supported [ 0.822415] rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine supported [ 0.823258] rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported [ 0.823885] rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported [ 0.824529] rk_gmac-dwmac fe010000.ethernet: TSO supported [ 0.824724] mmc1: SDHCI controller on fe310000.mmc [fe310000.mmc] using ADMA [ 0.825018] rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 0.826452] rk_gmac-dwmac fe010000.ethernet: device MAC address a6:b5:c8:f2:cc:06 [ 0.827 [ 0.855511] mmc_host mmc0: Bus speed (slot 0) = 375000Hz (slot req 375000Hz, actual 375000HZ div = 0) [ 0.909288] hub 1-1:1.0: USB hub found [ 0.909934] hub 1-1:1.0: 4 ports detected [ 0.937892] mmc_host mmc2: Bus speed (slot 0) = 150000000Hz (slot req 150000000Hz, actual 150000000HZ div = 0) [ 0.938935] mmc1: new high speed MMC card at address 0001 [ 0.940022] mmcblk1: mmc1:0001 58A431 14.6 GiB [ 0.965271] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 0.967536] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 0.968222] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 0.968989] platform regulatory.0: Falling back to sysfs fallback for: regulatory.db [ 0.969751] mmcblk1: p1 [ 0.970479] mmcblk1boot0: mmc1:0001 58A431 4.00 MiB [ 0.972372] mmcblk1boot1: mmc1:0001 58A431 4.00 MiB [ 0.974046] mmcblk1rpmb: mmc1:0001 58A431 4.00 MiB, chardev (236:0) [ 1.033792] ALSA device list: [ 1.034090] No soundcards found. [ 1.039684] EXT4-fs (mmcblk1p1): INFO: recovery required on readonly filesystem [ 1.040350] EXT4-fs (mmcblk1p1): write access will be enabled during recovery [ 1.049736] EXT4-fs (mmcblk1p1): recovery complete [ 1.050697] EXT4-fs (mmcblk1p1): mounted filesystem with ordered data mode. Quota mode: none. [ 1.051565] VFS: Mounted root (ext4 filesystem) readonly on device 179:1. [ 1.056445] devtmpfs: mounted [ 1.062082] Freeing unused kernel memory: 6400K [ 1.062703] Run /sbin/init as init process [ 1.063118] with arguments: [ 1.063390] /sbin/init [ 1.063637] with environment: [ 1.063921] HOME=/ [ 1.064138] TERM=linux [ 1.198862] usb 1-1.1: new full-speed USB device number 3 using xhci-hcd [ 1.219092] dwmmc_rockchip fe2c0000.mmc: Successfully tuned phase to 233 [ 1.224885] mmc2: new ultra high speed SDR104 SDIO card at address 0001 [ 1.378509] systemd[1]: System time before build time, advancing clock. [ 1.424755] input: Logitech USB Receiver as /devices/platform/fcc00000.usb/xhci-hcd.0.auto/usb1/1-1/1-1.1/1-1.1:1.0/0003:046D:C52B.0001/input/input1 [ 1.472607] NET: Registered PF_INET6 protocol family [ 1.475003] Segment Routing with IPv6 [ 1.475420] In-situ OAM (IOAM) with IPv6 [ 1.483673] hid-generic 0003:046D:C52B.0001: input: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-xhci-hcd.0.auto-1.1/input0 [ 1.488016] input: Logitech USB Receiver Mouse as /devices/platform/fcc00000.usb/xhci-hcd.0.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C52B.0002/input/input2 [ 1.489594] input: Logitech USB Receiver Consumer Control as /devices/platform/fcc00000.usb/xhci-hcd.0.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C52B.0002/input/input3 [ 1.499088] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 1.501886] systemd[1]: Detected architecture arm64. [ 1.551442] input: Logitech USB Receiver System Control as /devices/platform/fcc00000.usb/xhci-hcd.0.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C52B.0002/input/input4 [ 1.553136] hid-generic 0003:046D:C52B.0002: input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-xhci-hcd.0.auto-1.1/input1 [ 1.557717] hid-generic 0003:046D:C52B.0003: device has no listeners, quitting [ 1.567412] systemd[1]: Set hostname to . [ 1.716735] dw-apb-uart fe660000.serial: forbid DMA for kernel console [ 2.057885] systemd[1]: Queued start job for default target Graphical Interface. [ 6.954759] random: crng init done [ 6.955324] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 6.956426] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 7.005007] systemd[1]: Created slice system-getty.slice. [ 7.007269] systemd[1]: Created slice system-modprobe.slice. [ 7.009222] systemd[1]: Created slice system-serial\x2dgetty.slice. [ 7.010253] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ 7.011488] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 7.012397] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 7.013529] systemd[1]: Reached target Local Encrypted Volumes. [ 7.014324] systemd[1]: Reached target Paths. [ 7.014899] systemd[1]: Reached target Remote File Systems. [ 7.015538] systemd[1]: Reached target Slices. [ 7.016092] systemd[1]: Reached target Swap. [ 7.017058] systemd[1]: Listening on fsck to fsckd communication Socket. [ 7.018014] systemd[1]: Listening on initctl Compatibility Named Pipe. [ 7.019333] systemd[1]: Listening on Journal Audit Socket. [ 7.020384] systemd[1]: Listening on Journal Socket (/dev/log). [ 7.021470] systemd[1]: Listening on Journal Socket. [ 7.024654] systemd[1]: Listening on udev Control Socket. [ 7.025765] systemd[1]: Listening on udev Kernel Socket. [ 7.026445] systemd[1]: Reached target Sockets. [ 7.030429] systemd[1]: Mounting Huge Pages File System... [ 7.035077] systemd[1]: Mounting POSIX Message Queue File System... [ 7.040551] systemd[1]: Mounting Kernel Debug File System... [ 7.045391] systemd[1]: Mounting Kernel Trace File System... [ 7.053500] systemd[1]: Starting Restore / save the current clock... [ 7.058681] systemd[1]: Starting Set the console keyboard layout... [ 7.064037] systemd[1]: Starting Create list of static device nodes for the current kernel... [ 7.069627] systemd[1]: Starting Load Kernel Module configfs... [ 7.075556] systemd[1]: Starting Load Kernel Module fuse... [ 7.083093] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 7.088324] systemd[1]: Starting File System Check on Root Device... [ 7.095013] systemd[1]: Starting Journal Service... [ 7.104501] fuse: init (API version 7.37) [ 7.107472] systemd[1]: Starting Load Kernel Modules... [ 7.112765] systemd[1]: Starting Coldplug All udev Devices... [ 7.128983] systemd[1]: Mounted Huge Pages File System. [ 7.130252] systemd[1]: Mounted POSIX Message Queue File System. [ 7.131856] systemd[1]: Mounted Kernel Debug File System. [ 7.133176] systemd[1]: Mounted Kernel Trace File System. [ 7.136629] systemd[1]: Finished Restore / save the current clock. [ 7.140324] systemd[1]: Finished Create list of static device nodes for the current kernel. [ 7.142480] systemd[1]: modprobe@configfs.service: Succeeded. [ 7.145549] systemd[1]: Finished Load Kernel Module configfs. [ 7.147794] systemd[1]: modprobe@fuse.service: Succeeded. [ 7.150416] systemd[1]: Finished Load Kernel Module fuse. [ 7.156191] systemd[1]: Finished Load Kernel Modules. [ 7.162366] systemd[1]: Mounting FUSE Control File System... [ 7.169406] systemd[1]: Mounting Kernel Configuration File System... [ 7.174977] systemd[1]: Started File System Check Daemon to report status. [ 7.180699] systemd[1]: Starting Apply Kernel Variables... [ 7.186601] systemd[1]: Mounted FUSE Control File System. [ 7.203158] systemd[1]: Mounted Kernel Configuration File System. [ 8.172283] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6 [ 8.547472] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Sep 18 2020 02:27:58 version 7.45.221 (3a6d3a0 CY) FWID 01-bbd9282b