DM36x initialization passed! UBL Product Vesion : DJI-GSP-UBL-1.0-rc10(2014-08-15) Dji UBL Version: 1.51(Aug 15 2014 - 17:05:12) Booting Catalog Boot Loader BootMode = NAND Starting NAND Copy... Valid magicnum, 0xA1ACED66, found in block 0x00000019. Uboot Checksum:0x7E25B44B Actua Checksum:0x7E25B44B U-Boot Product Vesion : DJI-GSP-Uboot-1.0-rc4(2014-07-23) U-Boot 2010.12-rc2-svn-Dji (Jul 23 2014 - 11:14:40) Cores: ARM 432 MHz DDR: 297 MHz I2C: ready DRAM: 128 MiB NAND: 128 MiB Bad block table found at page 65472, version 0x01 Bad block table found at page 65408, version 0x01 *** Warning - bad CRC, using default environment Net: Ethernet PHY: GENERIC @ 0xff DaVinci-EMAC Press ESC to abort autoboot in 1 seconds Loading from nand0, offset 0x4a0000 ** Unknown image type Wrong Image Format for bootm command ERROR: can't get kernel image! Loading from nand0, offset 0x900000 Image Name: Linux-2.6.32.17-davinci1 Created: 2015-03-30 9:54:39 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4032832 Bytes = 3.8 MiB Load Address: 80008000 Entry Point: 80008000 ## Booting kernel from Legacy Image at 80700000 ... Image Name: Linux-2.6.32.17-davinci1 Created: 2015-03-30 9:54:39 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4032832 Bytes = 3.8 MiB Load Address: 80008000 Entry Point: 80008000 Loading Kernel Image ... OK OK Starting kernel ... [ 0.000000] Kernel Product Vesion : DJI-NOHDMI-WM610-Kernel-1.0-rc6(2015-03-30) [ 0.000000] Linux version 2.6.32.17-davinci1 (root@dji) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #16 PREEMPT Mon Mar 30 17:54:38 HKT 2015 [ 0.000000] CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: DaVinci DM36x EVM [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] DaVinci dm36x_rev1.2 variant 0x8 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pages: 12192 [ 0.000000] Kernel command line: console=ttyS0,115200n8 rw dm365_imp.oper_mode=0 video=davincifb:vid0=0,10K:vid1=0,10K:osd0=1920x1080X16,8100K mem=48MB davinci_enc_mngr.ch0_output=COMPOSITE davinci_enc_mngr.ch0_mode=pal ubi.mtd=2,2048 root=ubi0:rootfs rootfstype=ubifs ip=off lpj=1077248 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Memory: 48MB = 48MB total [ 0.000000] Memory: 44452KB available (3640K code, 451K data, 116K init, 0K highmem) [ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:245 [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Calibrating delay loop (skipped) preset value.. 215.44 BogoMIPS (lpj=1077248) [ 0.000000] Mount-cache hash table entries: 512 [ 0.000000] CPU: Testing write buffer coherency: ok [ 0.000000] DaVinci: 8 gpio irqs [ 0.000000] NET: Registered protocol family 16 [ 0.110000] bio: create slab at 0 [ 0.110000] DM365 IPIPE initialized in Continuous mode [ 0.110000] SCSI subsystem initialized [ 0.120000] usbcore: registered new interface driver usbfs [ 0.120000] usbcore: registered new interface driver hub [ 0.120000] usbcore[ 3.820000] CMEMK module: built on Jan 13 2015 at 19:24:09 [ 3.820000] Reference Linux version 2.6.32 [ 3.840000] File /home/DJI2/Project/enc_nohdmi_wm610/src/dvsdk/dvsdk_dm368_4_02_00_06/linuxutils_2_26_01_02/packages/ti/sdo/linuxutils/cmem/src/module/cmemk.c [ 3.860000] allocated heap buffer 0xc7000000 of size 0x2456000 [ 3.890000] heap fallback enabled - will try heap if pool buffer is not available [ 3.890000] CMEM Range Overlaps Kernel Physical - allowing overlap [ 3.900000] CMEM phys_start (0x1000) overlaps kernel (0x80000000 -> 0x83000000) [ 3.910000] cmemk initialized [ 3.940000] IRQK module: built on Jan 13 2015 at 19:23:41 [ 3.960000] Reference Linux version 2.6.32 [ 3.960000] File /home/DJI2/Project/enc_nohdmi_wm610/src/dvsdk/dvsdk_dm368_4_02_00_06/linuxutils_2_26_01_02/packages/ti/sdo/linuxutils/irq/src/module/irqk.c [ 3.980000] irqk initialized [ 4.030000] EDMAK module: built on Jan 13 2015 at 19:23:04 [ 4.030000] Reference Linux version 2.6.32 [ 4.050000] File /home/DJI2/Project/enc_nohdmi_wm610/src/dvsdk/dvsdk_dm368_4_02_00_06/linuxutils_2_26_01_02/packages/ti/sdo/linuxutils/edma/src/module/edmak.c [ 4.160000] 68013 connected [ 4.160000] usbcore: registered new interface driver usb_68013 [ 4.190000] usb 68013 module init ok sulogin: no password entry for root login[446]: root login on 'ttyS0' #Process /etc/profile... root@Dji-Pro:~# encode_usb V00.02.02.00(Nov 3 2015 11:23:52). Entry Encrypt qury mode Auto to detect v[ 6.500000] EVM: switch to ambarella video input ideo input type: Default video input selected:Hdmi_yuv Setting video standard to: 0x100000000000000 Capture i[ 6.510000] davinci_resizer davinci_resizer.2: RSZ_G_CONFIG:0:1:124 nput set to Hdmi[ 6.520000] davinci_previewer davinci_previewer.2: ipipe_set_preview_config _yuv:11 [ 6.530000] vpfe-capture vpfe-capture: IPIPE Chained [ 6.530000] vpfe-capture vpfe-capture: Resizer present Capture videoStd[ 6.540000] EVM: switch to ambarella video input Old=0000000b [ 6.550000] vpfe-capture vpfe-capture: width = 1280, height = 720, bpp = 1 [ 6.550000] vpfe-capture vpfe-capture: adjusted width = 1280, height = 720, bpp = 1, bytesperline = 1280, sizeimage = 1382400 [ 6.570000] vpfe-capture vpfe-capture: width = 1280, height = 720, bpp = 1 [ 6.570000] vpfe-capture vpfe-capture: adjusted width = 1280, height = 720, bpp = 1, bytesperline = 1280, sizeimage = 1382400 videoFrameRate=30000, width=1280, height=720 Venc1.c : minNumOutBufs 2, minOutBufSize[0] 1382400, minOutBufSize[1] 800 GOP interval:30, outBufSize:1382400, enAdpBW:1, airRate=0, slice=6, VUI=4,timeScale=60001 osdThrFxn: process ID is 451 *********** watchdog timeout:5 ctrlThrFxn: process ID is 443 *********** GetFPGAstatus err! FPGA[1,0,1,0]-1.000000:0 hdmi status is 1 ARM Load: 51% Video fps: 0 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:02 Resolution: 1280x720 GetFPGAstatus err! FPGA[1,0,1,0]-1.000000:0 hdmi status is 1 video lost ARM Load: 1% Video fps: 0 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:03 Resolution: 1280x720 GetFPGAstatus err! FPGA[1,0,1,0]-1.000000:0 hdmi status is 1 video lost ARM Load: 2% Video fps: 0 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:04 Resolution: 1280x720 GetFPGAstatus err! FPGA[1,0,1,0]-1.000000:0 hdmi status is 1 video lost ARM Load: 1% Video fps: 0 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:05 Resolution: 1280x720 GetFPGAstatus err! FPGA[1,0,1,0]-1.000000:0 hdmi status is 1 video lost ARM Load: 0% Video fps: 0 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:06 Resolution: 1280x720 GetFPGAstatus err! FPGA[1,0,1,0]-1.000000:0 hdmi status is 1 video lost ARM Load: 2% Video fps: 0 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:07 Resolution: 1280x720 GetFPGAstatus err! FPGA[1,0,1,0]-1.000000:0 hdmi status is 1 video lost ARM Load: 0% Video fps: 0 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:08 Resolution: 1280x720 GetFPGAstatus err! FPGA[1,0,1,0]-1.000000:0 hdmi status is 1 video lost ARM Load: 3% Video fps: 0 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:09 Resolution: 1280x720 GetFPGAstatus err! FPGA[1,0,1,0]-1.000000:0 hdmi status is 1 video lost ARM Load: 2% Video fps: 0 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:10 Resolution: 1280x720 GetFPGAstatus err! FPGA[1,0,1,0]-1.000000:0 hdmi status is 1 video lost ARM Load: 2% Video fps: 0 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:11 Resolution: 1280x720 GetFPGAstatus err! FPGA[1,0,1,0]-1.000000:0 hdmi status is 1 video lost ARM Load: 2% Video fps: 0 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:12 Resolution: 1280x720 GetFPGAstatus err! FPGA[1,0,1,0]-1.000000:0 hdmi status is 1 video lost ARM Load: 3% Video fps: 0 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:13 Resolution: 1280x720 GetFPGAstatus err! FPGA[1,0,1,0]-1.000000:0 hdmi status is 1 video lost ARM Load: 2% Video fps: 0 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:14 Resolution: 1280x720 GetFPGAstatus err! FPGA[1,0,1,0]-1.000000:0 hdmi status is 1 video lost ARM Load: 2% Video fps: 0 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:15 Resolution: 1280x720 GetFPGAstatus err! FPGA[1,0,1,0]-1.000000:0 hdmi status is 1 video lost ARM Load: 2% Video fps: 0 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:16 Resolution: 1280x720 GetFPGAstatus err! FPGA[1,0,1,0]-1.000000:0 hdmi status is 1 video lost ARM Load: 0% Video fps: 0 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:17 Resolution: 1280x720 GetFPGAstatus err! FPGA[1,0,1,0]-1.000000:0 hdmi status is 1 video lost ARM Load: 0% Video fps: 0 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:18 Resolution: 1280x720 GetFPGAstatus err! FPGA[1,0,1,0]-1.000000:0 hdmi status is 1 video lost ARM Load: 2% Video fps: 0 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:19 Resolution: 1280x720 GetFPGAstatus err! FPGA[1,0,1,0]-1.000000:0 hdmi status is 1 video lost ARM Load: 2% Video fps: 0 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:20 Resolution: 1280x720 GetFPGAstatus err! FPGA[1,0,1,0]-1.000000:0 hdmi status is 1 video lost ARM Load: 1% Video fps: 0 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:21 Resolution: 1280x720 GetFPGAstatus err! FPGA[1,0,1,0]-1.000000:0 hdmi status is 1 video lost ARM Load: 1% Video fps: 0 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:22 Resolution: 1280x720 GetFPGAstatus err! FPGA[1,0,1,0]-1.000000:0 hdmi status is 1 video lost ARM Load: 1% Video fps: 0 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:23 Resolution: 1280x720 GetFPGAstatus err! FPGA[1,0,1,0]-1.000000:0 hdmi status is 1 video lost ARM Load: 1% Video fps: 0 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:24 Resolution: 1280x720 GetFPGAstatus err! FPGA[1,0,1,0]-1.000000:0 hdmi status is 1 video lost ARM Load: 1% Video fps: 0 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:25 Resolution: 1280x720 GetFPGAstatus err! FPGA[1,0,1,0]-1.000000:0 hdmi status is 1 video lost ARM Load: 2% Video fps: 0 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:26 Resolution: 1280x720 GetFPGAstatus err! FPGA[1,0,1,0]-1.000000:0 hdmi status is 1 video lost ARM Load: 2% Video fps: 0 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:27 Resolution: 1280x720 GetFPGAstatus err! FPGA[1,0,1,0]-1.000000:0 hdmi status is 1 video lost ARM Load: 2% Video fps: 0 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:28 Resolution: 1280x720 GetFPGAstatus err! FPGA[1,0,1,0]-1.000000:0 hdmi status is 1 video lost ARM Load: 2% Video fps: 0 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:29 Resolution: 1280x720