1. .DM36x initialization passed!
2. UBL Product Vesion : DJI-297M-UBL-1.0-rc0(2015-10-30)
3. Dji UBL Version: 1.51(Nov  2 2015 - 15:45:39)
4. Booting Catalog Boot Loader
5. BootMode = NAND
6. Starting NAND Copy...
7. Valid magicnum, 0xA1ACED66, found in block 0x00000019.
8.    DONE
9. Jumping to entry point at 0x81080000.
10.  
11. U-Boot Product Vesion : DJI-ENC-Uboot-1.0-rc0(2015-11-02)
12. U-Boot 2010.12-rc2-svn3205-Dji (Nov 02 2015 - 19:07:26)
13. Cores: ARM 297 MHz
14. DDR:   270 MHz
15. I2C:   ready
16. DRAM:  128 MiB
17. NAND:  128 MiB
18. MMC:   davinci: 0
19. Bad block table found at page 65472, version 0x01
20. Bad block table found at page 65408, version 0x01
21. nand_read_bbt: Bad block at 0x0000026e0000
22. nand_read_bbt: Bad block at 0x000007d40000
23. *** Warning - bad CRC, using default environment
24.  
25. Net:   Ethernet PHY: GENERIC @ 0xff
26. DaVinci-EMAC
27. Press ESC to abort autoboot in 1 seconds
28.  
29. Loading from nand0, offset 0x4a0000
30.    Image Name:   Linux-2.6.32.17-davinci1
31.    Created:      2015-11-02   7:28:36 UTC
32.    Image Type:   ARM Linux Kernel Image (uncompressed)
33.    Data Size:    4050848 Bytes = 3.9 MiB
34.    Load Address: 80008000
35.    Entry Point:  80008000
36. ## Booting kernel from Legacy Image at 80700000 ...
37.    Image Name:   Linux-2.6.32.17-davinci1
38.    Created:      2015-11-02   7:28:36 UTC
39.    Image Type:   ARM Linux Kernel Image (uncompressed)
40.    Data Size:    4050848 Bytes = 3.9 MiB
41.    Load Address: 80008000
42.    Entry Point:  80008000
43.    Loading Kernel Image ... OK
44. OK
45.  
46. Starting kernel ...
47.  
48. [    0.000000] Kernel Product Vesion : DJI-WIFI-WM610-Kernel-1.0-rc4(Nov  2 2015-15:24:51)
49. [    0.000000] Linux version 2.6.32.17-davinci1 (root@xueb-VirtualBox) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #1 PREEMPT Mon Nov 2 15:28:34 CST 2015
50. [    0.000000] CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
51. [    0.000000] CPU: VIVT data cache, VIVT instruction cache
52. [    0.000000] Machine: DaVinci DM36x EVM
53. [    0.000000] Memory policy: ECC disabled, Data cache writeback
54. [    0.000000] DaVinci dm36x_rev1.2 variant 0x8
55. [    0.000000] Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 12192
56. [    0.000000] Kernel command line: console=ttyS0,115200n8 rw dm365_imp.oper_mode=0 video=davincifb:vid0=0,0:vid1=0,0:osd0=0,0:osd1=0,0 mem=48MB davinci_enc_mngr.ch0_output=COMPOSITE davinci_enc_mngr.ch0_mode=pal ubi.mtd=2,2048 root=ubi0:rootfs rootfstype=ubifs ip=off lpj=1077248
57. [    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
58. [    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
59. [    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
60. [    0.000000] Memory: 48MB = 48MB total
61. [    0.000000] Memory: 44432KB available (3652K code, 453K data, 120K init, 0K highmem)
62. [    0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
63. [    0.000000] Hierarchical RCU implementation.
64. [    0.000000] NR_IRQS:245
65. [    0.000000] Console: colour dummy device 80x30
66. [    0.000000] Calibrating delay loop (skipped) preset value.. 215.44 BogoMIPS (lpj=1077248)
67. [    0.000000] Mount-cache hash table entries: 512
68. [    0.000000] CPU: Testing write buffer coherency: ok
69. [    0.000000] DaVinci: 8 gpio irqs
70. [    0.000000] NET: Registered protocol family 16
71. [    0.130000] bio: create slab <bio-0> at 0
72. [    0.140000] DM365 IPIPE initialized in Continuous mode
73. [    0.140000] SCSI subsystem initialized
74. [    0.140000] usbcore: registered new interface driver usbfs
75. [    0.150000] usbcore: registered new interface driver hub
76. [    0.150000] usbcore: registered new device driver usb
77. [    0.150000] davinci_i2c_probe
78. [    0.150000] vpss vpss: dm365_vpss vpss probed
79. [    0.150000] vpss vpss: dm365_vpss vpss probe success
80. [    0.150000] dm365_afew_hw_init
81. [    0.160000] ch0 default output "COMPOSITE", mode "PAL"
82. [    0.160000] VPBE Encoder Initialized
83. [    0.160000] LogicPD encoder initialized
84. [    0.160000] Switching to clocksource timer0_1
85. [    0.170000] musb_hdrc: version 6.0, pio, host, debug=0
86. [    0.190000] musb_hdrc: USB Host mode controller at fec64000 using PIO, IRQ 12
87. [    0.190000] musb_hdrc musb_hdrc: MUSB HDRC host driver
88. [    0.190000] musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
89. [    0.190000] usb usb1: configuration #1 chosen from 1 choice
90. [    0.190000] hub 1-0:1.0: USB hub found
91. [    0.190000] hub 1-0:1.0: 1 port detected
92. [    0.190000] NET: Registered protocol family 2
93. [    0.190000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
94. [    0.190000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
95. [    0.190000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
96. [    0.190000] TCP: Hash tables configured (established 2048 bind 2048)
97. [    0.190000] TCP reno registered
98. [    0.190000] NET: Registered protocol family 1
99. [    0.190000] RPC: Registered udp transport module.
100. [    0.190000] RPC: Registered tcp transport module.
101. [    0.190000] RPC: Registered tcp NFSv4.1 backchannel transport module.
102. [    0.200000] JFFS2 version 2.2. (NAND) ¬© 2001-2006 Red Hat, Inc.
103. [    0.200000] msgmni has been set to 86
104. [    0.210000] alg: No test for stdrng (krng)
105. [    0.210000] io scheduler noop registered (default)
106. [    0.240000] VBUS on (a_wait_vrise), devctl 19
107. [    0.290000] DM365 IPIPEIF probed
108. [    0.290000] imp serializer initialized
109. [    0.290000] davinci_previewer initialized
110. [    0.300000] davinci_resizer initialized
111. [    0.300000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
112. [    0.300000] serial8250.0: ttyS0 at MMIO 0x1c20000 (irq = 40) is a 16550A
113. [    0.660000] console [ttyS0] enabled
114. [    0.670000] serial8250.0: ttyS1 at MMIO 0x1d06000 (irq = 41) is a 16550A
115. [    0.680000] brd: module loaded
116. [    0.690000] NAND device: Manufacturer ID: 0xc2, Chip ID: 0xf1 (Unknown NAND 128MiB 3,3V 8-bit)
117. [    0.700000] Creating 4 MTD partitions on "davinci_nand.0":
118. [    0.700000] 0x000000000000-0x0000004a0000 : "bootloader"
119. [    0.710000] 0x0000004a0000-0x000000e00000 : "kernel"
120. [    0.720000] 0x000000e00000-0x000007f00000 : "filesystem"
121. [    0.730000] 0x000000000000-0x000008000000 : "all"
122. [    0.740000] davinci_nand davinci_nand.0: controller rev. 2.3
123. [    0.750000] UBI: attaching mtd2 to ubi0
124. [    0.750000] UBI: physical eraseblock size:   131072 bytes (128 KiB)
125. [    0.760000] UBI: logical eraseblock size:    126976 bytes
126. [    0.770000] UBI: smallest flash I/O unit:    2048
127. [    0.770000] UBI: sub-page size:              512
128. [    0.780000] UBI: VID header offset:          2048 (aligned 2048)
129. [    0.780000] UBI: data offset:                4096
130. [    0.950000] usb 1-1: new high speed USB device using musb_hdrc and address 2
131. [    1.100000] usb 1-1: configuration #1 chosen from 1 choice
132. [    1.320000] UBI: attached mtd2 to ubi0
133. [    1.320000] UBI: MTD device name:            "filesystem"
134. [    1.330000] UBI: MTD device size:            113 MiB
135. [    1.340000] UBI: number of good PEBs:        902
136. [    1.340000] UBI: number of bad PEBs:         2
137. [    1.340000] UBI: max. allowed volumes:       128
138. [    1.350000] UBI: wear-leveling threshold:    4096
139. [    1.350000] UBI: number of internal volumes: 1
140. [    1.360000] UBI: number of user volumes:     1
141. [    1.360000] UBI: available PEBs:             0
142. [    1.370000] UBI: total number of reserved PEBs: 902
143. [    1.370000] UBI: number of PEBs reserved for bad PEB handling: 9
144. [    1.380000] UBI: max/mean erase counter: 20/1
145. [    1.380000] UBI: image sequence number: 70871224
146. [    1.390000] UBI: background thread "ubi_bgt0d" started, PID 326
147. [    1.400000] usbcore: registered new interface driver asix
148. [    1.400000] usbcore: registered new interface driver cdc_ether
149. [    1.410000] usbcore: registered new interface driver net1080
150. [    1.420000] usbcore: registered new interface driver cdc_subset
151. [    1.420000] usbcore: registered new interface driver zaurus
152. [    1.430000] console [netcon0] enabled
153. [    1.430000] netconsole: network logging started
154. [    1.440000] Initializing USB Mass Storage driver...
155. [    1.440000] usbcore: registered new interface driver usb-storage
156. [    1.450000] USB Mass Storage support registered.
157. [    1.460000] i2c /dev entries driver
158. [    1.460000] Linux video capture interface: v2.00
159. [    1.520000] usb 1-1: USB disconnect, address 2
160. [    1.940000] usb 1-1: new high speed USB device using musb_hdrc and address 3
161. [    2.090000] usb 1-1: configuration #1 chosen from 1 choice
162. [    2.480000] i2c_davinci i2c_davinci.1: timeout when try recovery i2c bus
163. [    2.480000] i2c_davinci i2c_davinci.1: timeout waiting for bus ready
164. [    3.500000] i2c_davinci i2c_davinci.1: timeout when try recovery i2c bus
165. [    3.500000] i2c_davinci i2c_davinci.1: timeout waiting for bus ready
166. [    4.520000] i2c_davinci i2c_davinci.1: timeout when try recovery i2c bus
167. [    4.520000] i2c_davinci i2c_davinci.1: timeout waiting for bus ready
168. [    4.530000] vpfe-capture: vpss clock vpss_master enabled
169. [    4.530000] vpfe-capture vpfe-capture: v4l2 device registered
170. [    4.540000] vpfe-capture vpfe-capture: video device registered
171. [    4.550000] EVM: switch to ambarella video input
172. [    4.550000] vpfe-capture vpfe-capture: v4l2 sub device ambarella registered
173. [    4.560000] vpfe_register_ccdc_device: DM365 ISIF
174. [    4.570000] DM365 ISIF is registered with vpfe.
175. [    4.570000] Trying to register davinci display video device.
176. [    4.580000] layer=c1186000,layer->video_dev=c1186164
177. [    4.590000] Trying to register davinci display video device.
178. [    4.590000] layer=c1186400,layer->video_dev=c1186564
179. [    4.600000] davinci_init:DaVinci V4L2 Display Driver V1.0 loaded
180. [    4.600000] watchdog watchdog: heartbeat 1 sec
181. [    4.610000] ip_tables: (C) 2000-2006 Netfilter Core Team
182. [    4.620000] arp_tables: (C) 2002 David S. Miller
183. [    4.620000] TCP cubic registered
184. [    4.620000] NET: Registered protocol family 17
185. [    4.630000] Bridge firewalling registered
186. [    4.660000] Clocks: disable unused mmcsd0
187. [    4.660000] Clocks: disable unused mmcsd1
188. [    4.660000] Clocks: disable unused spi0
189. [    4.660000] Clocks: disable unused spi1
190. [    4.660000] Clocks: disable unused spi2
191. [    4.660000] Clocks: disable unused spi3
192. [    4.660000] Clocks: disable unused spi4
193. [    4.660000] Clocks: disable unused pwm0
194. [    4.660000] Clocks: disable unused pwm1
195. [    4.660000] Clocks: disable unused pwm2
196. [    4.660000] Clocks: disable unused pwm3
197. [    4.660000] Clocks: disable unused timer1
198. [    4.660000] Clocks: disable unused timer3
199. [    4.660000] Clocks: disable unused emac
200. [    4.660000] Clocks: disable unused voice_codec
201. [    4.660000] Clocks: disable unused asp0
202. [    4.660000] Clocks: disable unused rto
203. [    4.660000] Clocks: disable unused mjcp
204. [    4.740000] nnnn===0
205. [    4.740000] davinci_emac_probe: using random MAC addr: 36:bf:a7:a0:d0:eb
206. [    4.750000] emac-mii: probed
207. [    4.790000] UBIFS: recovery needed
208. [    4.820000] UBIFS: recovery completed
209. [    4.830000] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
210. [    4.830000] UBIFS: file system size:   110342144 bytes (107756 KiB, 105 MiB, 869 LEBs)
211. [    4.840000] UBIFS: journal size:       9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
212. [    4.850000] UBIFS: media format:       w4/r0 (latest is w4/r0)
213. [    4.850000] UBIFS: default compressor: lzo
214. [    4.860000] UBIFS: reserved for root:  0 bytes (0 KiB)
215. [    4.860000] VFS: Mounted root (ubifs filesystem) on device 0:13.
216. [    4.870000] Freeing init memory: 120K
217.  
218. >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>WM610<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
219.  
220. Filesystem Product Vesion : DJI-WM610-Filesystem-1.0-rc3(2014-06-06)
221. Runing /etc/init.d/rcS
222. [    7.020000] CMEMK module: built on Jan 13 2015 at 19:24:09
223. [    7.020000]   Reference Linux version 2.6.32
224. [    7.040000]   File /home/DJI2/Project/enc_nohdmi_wm610/src/dvsdk/dvsdk_dm368_4_02_00_06/linuxutils_2_26_01_02/packages/ti/sdo/linuxutils/cmem/src/module/cmemk.c
225. [    7.060000] allocated heap buffer 0xc7000000 of size 0x2456000
226. [    7.090000] heap fallback enabled - will try heap if pool buffer is not available
227. [    7.090000] CMEM Range Overlaps Kernel Physical - allowing overlap
228. [    7.110000] CMEM phys_start (0x1000) overlaps kernel (0x80000000 -> 0x83000000)
229. [    7.110000] cmemk initialized
230. [    7.160000] IRQK module: built on Jan 13 2015 at 19:23:41
231. [    7.160000]   Reference Linux version 2.6.32
232. [    7.180000]   File /home/DJI2/Project/enc_nohdmi_wm610/src/dvsdk/dvsdk_dm368_4_02_00_06/linuxutils_2_26_01_02/packages/ti/sdo/linuxutils/irq/src/module/irqk.c
233. [    7.200000] irqk initialized
234. [    7.260000] EDMAK module: built on Jan 13 2015 at 19:23:04
235. [    7.280000]   Reference Linux version 2.6.32
236. [    7.280000]   File /home/DJI2/Project/enc_nohdmi_wm610/src/dvsdk/dvsdk_dm368_4_02_00_06/linuxutils_2_26_01_02/packages/ti/sdo/linuxutils/edma/src/module/edmak.c
237. [    7.430000] 68013 connected
238. [    7.430000] usbcore: registered new interface driver usb_68013
239. [    7.460000] usb 68013 module init ok
240. sulogin: no password entry for root
241. login[445]: root login on 'ttyS0'
242.  
243. #Process /etc/profile...
244. root@Dji-Pro:~#
245.  
246. encode_usb V00.02.02.00(Nov  3 2015 11:23:52).
247. Entry Encrypt qury mode
248. Auto to detect v[    9.810000] EVM: switch to ambarella video input
249. ideo input type:
250. Default video input selected:Hdmi_yuv
251. Setting video standard to: 0x100000000000000
252. Capture input set to Hdmi[    9.830000] davinci_resizer davinci_resizer.2: RSZ_G_CONFIG:0:1:124
253. _yuv:11
254. [    9.830000] davinci_previewer davinci_previewer.2: ipipe_set_preview_config
255. [    9.840000] vpfe-capture vpfe-capture: IPIPE Chained
256. [    9.850000] vpfe-capture vpfe-capture: Resizer present
257. Capture videoStd[    9.850000] EVM: switch to ambarella video input
258. Old=0000000b
259. [    9.860000] vpfe-capture vpfe-capture: width = 1280, height = 720, bpp = 1
260. [    9.870000] vpfe-capture vpfe-capture: adjusted width = 1280, height = 720, bpp = 1, bytesperline = 1280, sizeimage = 1382400
261. [    9.880000] vpfe-capture vpfe-capture: width = 1280, height = 720, bpp = 1
262. [    9.880000] vpfe-capture vpfe-capture: adjusted width = 1280, height = 720, bpp = 1, bytesperline = 1280, sizeimage = 1382400
263. videoFrameRate=30000, width=1280, height=720
264. Venc1.c : minNumOutBufs 2, minOutBufSize[0] 1382400, minOutBufSize[1] 800
265. GOP interval:30, outBufSize:1382400, enAdpBW:1, airRate=0, slice=6, VUI=4,timeScale=60001
266. osdThrFxn: process ID is 450 ***********
267. watchdog timeout:5
268. ctrlThrFxn: process ID is 442 ***********
269. Frmae:1 Pslice = 0, Islice = 8[44ms]
270. GetFPGAstatus err!
271. FPGA[1,0,1,0]-1.000000:0
272. hdmi status is 1
273. ARM Load: 66% Video fps: 8 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:02 Resolution: 1280x720
274.  
275. GetFPGAstatus err!
276. FPGA[1,0,1,0]-1.000000:0
277. hdmi status is 1
278. ARM Load: 6% Video fps: 7 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:03 Resolution: 1280x720
279.  
280. GetFPGAstatus err!
281. FPGA[1,0,1,0]-1.000000:0
282. hdmi status is 1
283. ARM Load: 5% Video fps: 8 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:04 Resolution: 1280x720
284.  
285. GetFPGAstatus err!
286. FPGA[1,0,1,0]-1.000000:0
287. hdmi status is 1
288. ARM Load: 11% Video fps: 8 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:05 Resolution: 1280x720
289.  
290. GetFPGAstatus err!
291. FPGA[1,0,1,0]-1.000000:0
292. hdmi status is 1
293. ARM Load: 17% Video fps: 7 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:06 Resolution: 1280x720
294.  
295. GetFPGAstatus err!
296. FPGA[1,0,1,0]-1.000000:0
297. hdmi status is 1
298. ARM Load: 11% Video fps: 8 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:07 Resolution: 1280x720
299.  
300. GetFPGAstatus err!
301. FPGA[1,0,1,0]-1.000000:0
302. hdmi status is 1
303. ARM Load: 5% Video fps: 7 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:08 Resolution: 1280x720
304.  
305. GetFPGAstatus err!
306. FPGA[1,0,1,0]-1.000000:0
307. hdmi status is 1
308. ARM Load: 8% Video fps: 8 fps Video bit rate: 0 kbps PHY Bandwidth: 0 kbps Time: 00:00:09 Resolution: 1280x720
309.