1. [stepper_x]
2. step_pin: ar54
3. dir_pin: ar55
4. enable_pin: !ar38
5. microsteps: 16
6. rotation_distance: 40
7. endstop_pin: ^!ar3
8. position_min: -7
9. position_endstop: -7
10. position_max: 303
11. homing_speed: 40.0
12.  
13. [stepper_y]
14. step_pin: ar60
15. dir_pin: ar61
16. enable_pin: !ar56
17. microsteps: 16
18. rotation_distance: 40
19. endstop_pin: ^!ar14
20. position_min: -7
21. position_endstop: -7
22. position_max: 303
23. homing_speed: 40
24. homing_positive_dir: false
25.  
26. [stepper_z]
27. step_pin: ar46
28. dir_pin: !ar48
29. enable_pin: !ar62
30. microsteps: 16
31. rotation_distance: 8
32. # endstop_pin: ^!ar18
33. endstop_pin: probe:z_virtual_endstop
34. # position_endstop: -1.70
35. position_min: -10
36. position_max: 400
37. homing_speed: 30
38. second_homing_speed: 1
39.  
40. [stepper_z1]
41. step_pin: ar36
42. dir_pin: !ar34
43. enable_pin: !ar30
44. microsteps: 16
45. rotation_distance: 8
46.  
47. [extruder]
48. step_pin: ar26
49. dir_pin: ar28
50. enable_pin: !ar24
51. microsteps: 16
52. rotation_distance: 7
53. nozzle_diameter: 0.400
54. filament_diameter: 1.750
55. heater_pin: ar10
56. sensor_type: EPCOS 100K B57560G104F
57. sensor_pin: analog13
58. min_extrude_temp: 50
59. min_temp: 5
60. max_temp: 240
61. max_extrude_only_distance: 500
62. max_extrude_cross_section: 2.0
63. control = pid
64. pid_kp = 21.465
65. pid_ki = 0.980
66. pid_kd = 117.521
67.  
68. [heater_bed]
69. heater_pin: ar8
70. sensor_type: EPCOS 100K B57560G104F
71. sensor_pin: analog14
72. min_temp: 5
73. max_temp: 150
74. control = pid
75. pid_kp = 48.362
76. pid_ki = 0.638
77. pid_kd = 915.854
78.  
79. [fan]
80. pin: ar9
81. kick_start_time: 0.500
82.  
83. [heater_fan my_nozzle_fan]
84. pin:ar7
85. heater: extruder
86. heater_temp: 50.0
87. fan_speed: .7
88.  
89. [mcu]
90. #make sure this reflects your serial port you found when flashing klipper
91. serial: /dev/ttyUSB0
92. pin_map: arduino
93.  
94. [printer]
95. kinematics: cartesian
96. max_velocity: 200
97. max_accel: 3000
98. max_z_velocity: 50
99. max_z_accel: 100
100. square_corner_velocity: 5
101.  
102. [bed_screws]
103. screw1: 55,55
104. screw1_name: front left
105. screw2: 255,55
106. screw2_name: front right
107. screw3: 255,255
108. screw3_name: back right
109. screw4: 55,255
110. screw4_name: back left
111. speed: 100.0
112.  
113. [screws_tilt_adjust]
114. screw1: 22,83
115. screw1_name: front left
116. screw2: 222,83
117. screw2_name: front right
118. screw3: 22,283
119. screw3_name: back left
120. screw4: 222,283
121. screw4_name: back right
122. speed: 100.0
123. screw_thread: CW-M5
124.  
125. [bltouch]
126. sensor_pin = ^ar19
127. control_pin = ar11
128. pin_move_time = 0.5
129. x_offset = 29
130. y_offset = -38
131. z_offset = 2.761
132. speed:5
133. lift_speed: 20
134. samples: 3
135. samples_result: average
136.  
137. [safe_z_home]
138. home_xy_position: 150,150 # Change coordinates to the center of your print bed
139. speed: 50
140. z_hop: 15                 # Move up 15mm
141. z_hop_speed: 5
142.  
143. # Manual mesh settings
144. # [bed_mesh]
145. # speed: 150
146. # horizontal_move_z: 5
147. # mesh_min: 7,7
148. # mesh_max: 285, 285
149. # probe_count: 5,5
150.  
151. [bed_mesh]
152. speed: 150
153. horizontal_move_z: 5
154. mesh_min: 30, 30
155. mesh_max: 270, 265
156. probe_count: 5, 5
157. algorithm: bicubic
158. bicubic_tension: .1
159. relative_reference_index: 7
160. # fade_start: 0.6
161. # fade_end: 10.0
162. mesh_pps: 2,2
163.  
164. #*# <---------------------- SAVE_CONFIG ---------------------->
165. #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
166. #*#
167. #*# [bed_mesh default]
168. #*# version = 1
169. #*# points =
170. #*#       0.000000, -0.072500, -0.092500, -0.065000, -0.017500
171. #*#       -0.047500, -0.107500, -0.112500, -0.077500, -0.022500
172. #*#       -0.007500, -0.060000, -0.065000, -0.030000, 0.042500
173. #*#       -0.015000, -0.032500, -0.020000, 0.047500, 0.162500
174. #*#       -0.267500, -0.252500, -0.185000, -0.047500, 0.087500
175. #*# tension = 0.1
176. #*# min_x = 45.0
177. #*# algo = bicubic
178. #*# y_count = 5
179. #*# mesh_y_pps = 2
180. #*# min_y = 45.0
181. #*# x_count = 5
182. #*# max_y = 255.0
183. #*# mesh_x_pps = 2
184. #*# max_x = 255.0
185. #*#
186. #*# [bed_mesh base]
187. #*# version = 1
188. #*# points =
189. #*#       0.000000, -0.072500, -0.092500, -0.065000, -0.017500
190. #*#       -0.047500, -0.107500, -0.112500, -0.077500, -0.022500
191. #*#       -0.007500, -0.060000, -0.065000, -0.030000, 0.042500
192. #*#       -0.015000, -0.032500, -0.020000, 0.047500, 0.162500
193. #*#       -0.267500, -0.252500, -0.185000, -0.047500, 0.087500
194. #*# tension = 0.1
195. #*# min_x = 45.0
196. #*# algo = bicubic
197. #*# y_count = 5
198. #*# mesh_y_pps = 2
199. #*# min_y = 45.0
200. #*# x_count = 5
201. #*# max_y = 255.0
202. #*# mesh_x_pps = 2
203. #*# max_x = 255.0
204.